Garner, NC HVAC & Electrical

Completed comprehensive heating and air maintenance on 2013 HVAC unit including 80-point inspection, outdoor coil cleaning, burner cleaning, gas pressure adjustments, and safety inspections. Verified system temperature readings at 738.2°F and inspected electrical disconnect panel connections. All components operating within manufacturer specifications.

Responded to non-functioning electrical outlets in two bathrooms. Inspected main electrical panel and confirmed all circuit breakers were in proper position with no trips. Diagnosed GFCI protection issue affecting bathroom circuits. Reset and tested GFCI devices, restoring power to all bathroom outlets. Verified proper operation of all receptacles and provided estimate for installation of decorative lighting fixture above bookcase with perimeter mounting configuration.

Responded to service call for 10+ year old system experiencing reduced cooling and weak airflow following weekend outage. Performed diagnostic evaluation of unit that had recently received preventive maintenance. Used digital clamp meter to measure electrical parameters, recording voltage reading of 12.18V and current draw of 1125 at compressor circuit. Inspected capacitor, control board, and electrical connections. System was operational and cooling adequately at time of inspection, with homeowner reporting unit had cooled residence overnight despite reduced airflow.

Responded to after-hours no cooling call on 8-year-old system. Upon inspection, diagnosed failed run capacitor with 18.8µF reading, significantly below the rated 20µF specification. Replaced defective CBB65 450VAC capacitor, restored system to proper operation, and verified adequate airflow through vents.

Responded to service call for bathroom exhaust fan producing grinding noise and failing to ventilate properly. Upon inspection, tested airflow using digital measurement device and confirmed inadequate ventilation performance. Diagnosed mechanical failure in fan motor assembly, performed necessary repairs to restore proper operation and airflow, and verified system functionality upon completion.

Responded to possible recall for permit corrections on HVAC installation. Verified and labeled breaker for exterior condensing unit at meter base with proper identification. Inspected ductwork above indoor unit and confirmed all connections are secure and properly fastened. Documented installation with photographs showing outdoor unit, refrigerant lines, electrical disconnect, meter base, and all associated components in proper working condition.

Responded to service call at 2006-built residence for non-functioning three-way switches and basement lighting issues. Troubleshot two separate three-way switch circuits that were inoperative and diagnosed wiring faults at switch locations. Inspected electrical panel to verify circuit integrity and proper breaker operation for affected circuits. Addressed strip of four LED lights in drop ceiling basement that failed to illuminate, testing fixtures, drivers, and upstream wiring to isolate failure point. Restored functionality to both three-way switching systems and basement lighting circuit, verified proper operation of all repaired components, and documented panel configuration for service records.

Completed comprehensive heating and air maintenance on one HVAC unit, performing an 80-point inspection that included outdoor coil cleaning, burner cleaning, gas pressure adjustments, and full safety inspections. Inspected blower wheel assembly and verified proper operation of all system components. Installed new MERV 11 rated 16x20x4 air filter with correct airflow orientation to ensure optimal system performance and indoor air quality.

Completed electrical installation including exterior weather-resistant GFCI outlet with vinyl mounting box and protective cover on home's exterior siding. Installed two dimmer switches for interior lighting control in dining room and kitchen nook areas. Mounted three ceiling fans in upstairs bedrooms and master bedroom, with fan-rated electrical boxes verified and installed as needed to support fixtures safely. All work completed with materials and labor covered under warranty.

Performed diagnostic service on non-functioning rear yard light fixture. Upon inspection, identified faulty electrical connections within the outdoor lighting control box mounted in wooden enclosure. Tested electrical components including relay, contactor, and associated wiring connections to isolate the source of the malfunction. Completed necessary repairs to restore proper operation of the exterior lighting system.

Completed HVAC system installation including Friedrich outdoor condensing unit model WFPU17Y363D utilizing R454B refrigerant. Installed and programmed Honeywell Home digital thermostat on interior wall, configured for proper system operation and user interface. Equipment was transported to jobsite and positioned against exterior brick wall per installation specifications. All electrical connections completed, system tested and verified operational. Installation financed with down payment arrangement.

Removed existing zone damper assembly including motor and mounting hardware from the HVAC ductwork system. Installed new Honeywell zone damper with integrated motor and control module, securing it to the flexible ductwork in the attic space. Verified proper damper operation and control functionality upon completion.

Responded to service call for non-operational air conditioning system installed in 1994. Performed site assessment and documented existing electrical panel configuration and return air grille location for replacement system quote preparation. Provided comprehensive replacement options for aged HVAC equipment that has reached end of serviceable life.

Completed site assessment and provided quote for installation of RV electrical hookup at rear corner of 1994 residential property. Evaluated existing electrical service panel and meter configuration, photographed current setup showing main service entrance with meter enclosure and distribution boxes mounted on exterior wall above brick foundation, and determined routing requirements for new dedicated 50-amp RV receptacle circuit from main panel to proposed hookup location.

Completed installation of exterior weatherproof GFCI outlet with decorative mounting block and clear protective cover on vinyl siding. Installed two LED-compatible dimmer switches for separate light fixtures. Installed three ceiling fans: two units in upstairs locations with 8-foot ceiling heights and one unit in master bedroom with 10-12 foot ceiling height. All circuits properly connected at main electrical panel and tested for functionality.

Responded to after-hours emergency call for HVAC system running but producing no cool air. Upon arrival, performed diagnostic testing of the outdoor condensing unit using clamp meter to measure capacitance and electrical values. Testing revealed failed run capacitor reading 4323 microfarads, significantly outside manufacturer specifications. Accessed electrical panel to verify proper power supply and circuit integrity to the HVAC system. Identified capacitor failure as root cause preventing compressor from operating properly, resulting in fan-only operation without refrigeration cycle engagement.

Responded to a no-power complaint affecting the front porch, doorbell, and Ring camera system. Upon arrival, verified the circuit breaker was not tripped and conducted voltage testing at the affected circuits using a digital multimeter. Troubleshooting revealed a fault in the outdoor electrical junction box serving the front porch area. Inspected the weatherproof enclosure and identified compromised wiring connections due to moisture intrusion and corrosion. Repaired the damaged connections, restored power to all affected devices, and verified proper operation of the doorbell and camera system.

Responded to kitchen light switch failure in 1981 home where light initially flickered before complete loss of function. Inspected electrical panel and circuit breaker configuration, documented panel condition and external meter box installation. Troubleshot non-functioning kitchen light switch circuit to identify cause of failure and restore proper operation.

Completed comprehensive heating and air maintenance on 12-year-old system including 80-point inspection on each unit. Performed outdoor coil cleaning, burner cleaning, and adjusted gas pressures as needed. Verified electrical readings with clamp meter showing 350.2 amperage and applied treatment to evaporator coil assembly. All safety inspections passed with system operating within manufacturer specifications.

Responded to service call for blown fuse affecting garage and bathroom lighting circuits in 2014-built residence with no prior occurrences. Upon inspection of main electrical panel, identified tripped circuit breaker serving affected areas. Reset breaker, verified proper operation of all circuits, and confirmed power restoration to garage and bathroom lighting fixtures. Documented panel condition with photographs showing organized wiring installation and proper grounding connections.

Responded to service call for bathroom exhaust fan replacement consultation at 2010-built residence. Homeowner requested guidance on selecting appropriate replacement unit prior to installation. Performed electrical panel inspection and documentation, photographing residential breaker configuration with main disconnect and branch circuits serving all major home systems including HVAC, kitchen appliances, bathroom circuits, and general lighting loads. Provided technical recommendations on compatible exhaust fan specifications based on existing electrical infrastructure and bathroom circuit capacity for future installation scheduling.

Responded to no cooling complaint on 12-year-old dual-zone system with inadequate cooling performance reported on both upstairs and downstairs units. Performed diagnostic inspection of downstairs unit, documenting control board and capacitor assembly condition. Thermostat verified in cooling mode with setpoint at 71°F and current temperature reading of 78°F, confirming temperature differential and system underperformance.

Responded to emergency electrical call regarding burnt wiring in main breaker panel preventing AC unit operation. Upon arrival, inspected electrical panel and service equipment for signs of thermal damage, overheating, or compromised connections. Examined meter base, main disconnect, and associated conduit systems mounted on exterior wall. Evaluated wire integrity at junction points and verified proper connections at Generac transfer switch and main service panel. Identified and addressed burnt wire condition that had disabled HVAC system operation. Restored safe electrical service and verified proper function of all circuits to allow AC unit to be safely energized.

Investigated previously installed doorbell system that stopped functioning after third-party security service interaction, diagnosed internal chime malfunction, and scheduled return visit with required replacement parts. Completed annual 32-point electrical system evaluation including panel maintenance with torque verification, GFCI/AFCI protection testing, and smoke/CO2 detector servicing with battery replacement.

Responded to callback for recently installed HVAC system experiencing intermittent cooling with unit blowing warm air after initial cold output. Upon inspection, verified thermostat operation showing cooling mode active at 72°F setpoint with 78°F ambient temperature, confirmed proper airflow through supply ductwork in attic space, and examined installation components including main trunk line with insulation wrap and reflective radiant barrier. System operational at time of service call with no immediate defects identified in installation workmanship or equipment function.