Lillington, NC HVAC & Electrical

Responded to a service call for circuit breakers tripping after hardwired smoke alarm replacement. Upon arrival, performed voltage testing and circuit analysis to diagnose the electrical fault causing breaker trips. Identified wiring issues created during the smoke alarm installation that resulted in short circuits preventing proper breaker operation. Corrected the wiring connections, restored power to the smoke alarm circuit, and verified all hardwired fire alarms were functioning properly with no further breaker trips occurring.

Responded to a service call for a power outage affecting approximately half the home's lighting circuits after a grinder tool tripped a breaker. Upon arrival, investigated the electrical panel and circuit distribution system. Inspected the affected lighting circuits throughout the residence, including recessed ceiling fixtures and other lighting loads. Verified proper breaker operation and reset tripped circuit protection devices. Tested and confirmed restoration of power to all previously non-functional lighting circuits. Inspected exterior meter base and service entrance equipment to ensure no issues with main electrical service feed. All circuits returned to normal operation with lighting functioning properly throughout the home.

Responded to service call for heat pump system with no cooling capability after customer's son replaced Ecobee thermostat with Google Nest unit. Upon arrival, found yellow wire (Y-terminal for compressor cooling) improperly seated and backing out of thermostat terminal connection. Properly terminated yellow wire into Y-terminal, verified all thermostat wiring connections were secure and correctly landed per heat pump configuration, and tested system operation in both heating and cooling modes. System now functioning properly with both heat and air conditioning operational.

Installed two standard electrical outlets and one fan-rated receptacle in backyard pavilion structure, running appropriate wiring through wooden framing and ensuring proper grounding and code compliance. Additionally installed one GFCI-protected outlet on rear deck area to provide exterior power access. All installations tested and verified operational upon completion.

Replaced defective control board under warranty at office location. Verified system operation and confirmed proper electrical connections at main service panel. Measured and documented ambient temperature readings of 55.8°F to ensure HVAC system functionality post-repair.

Responded to service call for flickering lights throughout residence with aging electrical panel. Upon inspection, confirmed 50-year-old main breaker panel showing signs of deterioration and inadequate capacity for current electrical load. Documented existing conditions including outdated wiring in attic space with visible insulation damage on conductors and improper wire management at light fixtures. Evaluated electrical infrastructure in basement utility area where HVAC and water heater systems are located, noting multiple electrical connections and potential load concerns. Photographed deteriorated wiring conditions and aging electrical components to document safety concerns and recommend panel upgrade to meet current electrical code requirements and resolve flickering light issues.

Responded to request for ceiling fan box installation in upstairs area of newly constructed home. Upon inspection of attic space, confirmed existing electrical wiring was present and routed through framing members with proper insulation clearance. Assessed structural framing and electrical infrastructure to determine feasibility of installing ceiling fan-rated junction boxes at desired locations.

Conducted sales consultation for HVAC system replacement. Documented existing outdoor unit with severely deteriorated manufacturer label and aging equipment showing extensive weathering and corrosion. Discussed replacement options with homeowner for complete system upgrade.

Responded to service call for HVAC system experiencing irregular cycling and elevated energy consumption in 1957 construction home. Performed system inspection and accessed electrical control panel to evaluate thermostat controls, indicator lights, and wiring connections. Documented existing equipment configuration including control panel components and refrigerant line connections for air conditioning estimate as requested.

Completed scheduled preventative maintenance service on HVAC unit including comprehensive 80-point inspection. Performed system cleaning including outdoor coils and burners, adjusted gas pressures as needed, and conducted safety inspections. System temperature readings normal at 66.6°F with compressor and refrigerant lines in good working condition.

Performed diagnostic evaluation of HVAC system at vacant property with access provided via door code. Identified significant condensation issues on evaporator coil and conducted moisture measurements using UEI meter. Completed exterior unit cleaning service as requested by property owner who is preparing home for market.

Installed dedicated 15A/120V receptacle for drink machine in front office area to prevent circuit overload. Extended power from Panel C using EMT conduit to drop ceiling, then transitioned to MC cable for final run. Mounted commercial-grade receptacle and verified proper operation to eliminate the recurring breaker trips that were affecting existing lighting and receptacle circuit.

Responded to service call for a Blueridge mini-split system that was dripping water in bedroom and not cooling effectively. Upon inspection, found significant dust accumulation on evaporator coils and internal components affecting performance. Cleaned coils and verified proper system operation before completing service.

Completed installation of new HVAC system with connection to existing electrical infrastructure. Installed dedicated circuit breaker for dehumidifier and heat pump in main panel, and verified proper labeling of furnace and air handler unit connections in the secondary fuse box.

Performed comprehensive preventative maintenance on two HVAC systems (2017 conventional unit and 2022 mini-split) per POM agreement, including 80-point inspection on each unit, outdoor coil cleaning, burner cleaning, gas pressure adjustments, and safety inspections. Documented airflow issues in master bedroom and secondary bedroom; noted previous technician had indicated no remediation options available. Observed corrosion at metal junction points requiring future monitoring.

Completed 32-point electrical system evaluation on 20-year-old home, including panel maintenance with connection torquing and verification. Performed GFCI/Arc Fault protection testing and smoke/CO detector maintenance, noting insulation issues in wall/ceiling cavity requiring attention.

Successfully removed and thoroughly cleaned blower wheel from air handler as scheduled. Component exhibited significant dust accumulation that was impeding optimal airflow. Completed cleaning procedure outdoors using appropriate methods to restore proper functionality.

Diagnosed intermittent operation in master bedroom light fixture by examining the switch wiring. Removed switch plate to inspect the electrical connections, finding signs of wear at junction box. Documented existing conditions with photos showing the triple-gang switch configuration and exposed wiring for further assessment.

Conducted diagnostic assessment on 2020 system that was not cooling properly, focusing on the upstairs unit of a 3-system installation. Inspection revealed issues with thermostat wiring configuration, documented with photos of the thermostat baseplate showing multiple terminal connections (S, Y, Y2, G, O, U, W, K, R, Rc) with various colored wires and an unfinished wall opening. Also inspected exterior GE disconnect box mounted on beige siding with associated conduit connections.

Responded to no-cooling complaint for upstairs system in a residence with three HVAC units (2020 model). Diagnostic testing revealed faulty capacitor reading 28μF, which was confirmed using clamp meter. Replaced capacitor and verified proper system operation with normal cooling restored.

Responded to service call for ceiling fan balancing issue on a newly constructed residence (2023). Inspected mounting hardware and blade alignment, making necessary adjustments to eliminate wobble. Verified proper operation and balance of the 4-blade ceiling fan with attached light fixture after service completion.

Responded to service call regarding intermittent breaker tripping in bedroom occupied by resident on oxygen therapy. Performed thorough inspection of exterior electrical components including main panel, disconnects, and auxiliary equipment. No immediate issues identified with external electrical systems. Recommended installation of dedicated circuit for medical equipment to prevent future interruptions to critical power supply.

Diagnosed low voltage issue affecting garage door opener operation. Inspected GFCI outlet and electrical panel to verify power supply. Confirmed electrical service was functioning properly; issue isolated to garage door opener circuit requiring repair.

Successfully completed installation of a Mitsubishi Electric split-system heat pump (Model MUZ-WX09NL) with R454B refrigerant. Mounted outdoor condenser unit on concrete pad with proper drainage system using PVC piping, and installed disconnect box with appropriate electrical connections. All components were properly secured and tested for optimal performance.

Performed a 32-point electrical system evaluation on a 2003 home, focusing on the panel that services the dehumidifier which had been frequently tripping. Inspection revealed the furnace lacks a dedicated circuit as recommended. Completed maintenance including connection torquing, GFCI/Arc Fault breaker testing, and smoke/CO2 detector service, while documenting significant dust accumulation in the panel that required cleaning.